Rapid Model Slate Grey 1Lt
Out of stock
Additional information
| Weight | 1 kg |
|---|
Your Safety, Our Priority at Monocure3D
At Monocure3D, we place the utmost importance on the safety and well-being of our customers. Rest assured, every material we produce, proudly made in Australia, is designed to adhere to the highest safety standards in the industry. While we have formulated our resins to maximise safety, we strongly advise exercising caution during use. To ensure you have all the necessary information for safe handling, please follow the link below to download the Safety Data Sheet. These SDS’s are tailored according to the safety regulations of your specific country, ensuring you receive the most relevant and accurate safety guidelines.
Prototyping | Miniatures | Display models | Architecture models | Hobby models
RAPID MODEL RESIN FEATURES
Incredible Detail
A unique, epoxy-based resin prints at high detail 3d printing resin without brittleness.
Easy to Use
Give the bottle a shake, and the Rapid Model resin is ready to pour and print. No heating required.
Ultra Fast
Rapid Model Resins can print fast on all MSLA 3D printers, with 2 -3 second normal layers on most Monochrome 3D printers.
Huge Colour Range
Need some colour? Don’t print in just black and white. Available in various deep solid colours to make your models stand out.
About Rapid Model Resins
Monocure 3D Rapid Model Resins were initially developed with MSLA printers that use LED arrays to cure the resin. The unique, epoxy-based system creates models that process a hard surface finish without the brittleness you would expect.
This resin is easy to use; give the bottle a quick shake, then pour and print! The typical normal layer durations for an MSLA printer are approx. 2-3 seconds in a printer with a monochrome LCD Screen.
Our Rapid Resins should be post-cured for at least 20-30mins after cleaning. This ensures that the model will not crack or split over time. Please check our printer settings page for all the information to help you dial in your printer with our resin.
RAPID MODEL PRINTING TIPS
Ensure the resin is mixed well by shaking the bottle before every use.
Always ‘dial in’ your Printer using our Calibration Models.
For best results, clean Models with our ResinAway® solution.
To reduce the yellowing, try to Post-Cure using 405nm UV only.
Rapid model resins are versatile as they can be printed between 5 and 100-micron layer heights. To achieve the best results, 3D models should always be sliced solid, if hollowing is required, ensure drain holes are included to remove any trapped resin.
Always angle the model on the build plate to avoid large flat areas that might cause printing problems. These include warping and deformation due to the adhesion to the FEP film. To assist with unsupported areas, ensure you use dense, well-positioned, solid supports.
This resin might print faster than other resins on the market, please adjust your settings accordingly. Use a calibration model from our website to dial in your printer with our resin.
Check our printer setting page to see if we have your printer listed to give you a good starting point.
MECHANICAL PROPERTIES
Method Code: ASTM D638-14
Product: Monocure 3D RAPID Model Resins (25μm)
Acceptance Code: Supply Findings
Specimen Type: Retangular beam samples (Type IV)
Equip’ Serial No: UTM Serial No. 075
Conditioning: Tested at ambient temperature
SKUs
3DR-3582C, 3DR-3588GY, 3DR-3587BK, 3DR-3583W, 3DR-3585B, 3DR-3585GM
Cross-Sectional Area (mm2)
25.29
Max Force (kN)
1.64
Tensile Strength (MPa)
47
Elongation at Break
3.0
Young’s Modulus (GPa)
1.8
Flexural Band Span (mm)
86.23
Max Load Applied (N)
380
Flexural Stress (MPa)
124
Max Flex Strain (mm/mm)
0.5
Shore Hardness (D)
75
Heat Deflection Temp
55°C @ 0.45MPa
FINISHING — WHAT'S THE BEST PRACTICE?
- For best results after printing, use ResinAway® for removing uncured resin from the part. Place part in a pre-wash bath filled with ResinAway® and use a soft brush to remove excess resin. Follow by placing the component into an ultrasonic cleaner with ResinAway® for 3-5mins to help remove the resin trapped in the finer detail.
- Ensure parts are dry by using compressed air or patting gently with a lint-free cloth before post-curing – Warning: leaving excess IPA or ResinAway® on parts might result in surface cracking.
- We recommend using a 405nm LED Ultraviolet light to post-cure the model. It is recommended to post-cure for a few minutes, then remove the excess ResinAway® by washing with fresh water. Then place it back in the curing chamber for at least 30 mins to improve the tensile strength of the resin.
- When exposing a part to external elements, apply paint to the surface to improve longevity. Alternatively, the components can be machined, sanded and polished to create a tough scratch resistant surface.
PHYSICAL PROPERTIES
SKUs
3DR-3582C, 3DR-3588GY, 3DR-3587BK, 3DR-3583W, 3DR-3585B, 3DR-3585GM
Colour(s)
Clear (100% trans) Grey (5% trans), Black (10% trans), White (0% trans), Blue (10% trans), Gun Metal (0% trans)
Viscosity
500 – 600cps @ 25°C (Brookfield RVT)
Odour
Negligible Characteristics
Shelf Life
36 months
Active Solids
100%
UV Cure
225nm to 420nm
Cure Speed
2-3 secs Mono Screen
Storage
Dark cool & dry place
Wash Up
RESINAWAY® or IPA